2017-04-26 18:40:00 +03:00
|
|
|
# This file contains common pin mappings for RAMPS (v1.3 and later)
|
|
|
|
|
# boards. RAMPS boards typically use a firmware compiled for the AVR
|
|
|
|
|
# atmega2560 (though other AVR chips are also possible).
|
|
|
|
|
|
2020-11-17 02:47:32 +03:00
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
2017-04-26 18:40:00 +03:00
|
|
|
|
|
|
|
|
[stepper_x]
|
|
|
|
|
step_pin: ar54
|
|
|
|
|
dir_pin: ar55
|
|
|
|
|
enable_pin: !ar38
|
|
|
|
|
step_distance: .0125
|
|
|
|
|
endstop_pin: ^ar3
|
2017-07-24 20:17:18 +03:00
|
|
|
#endstop_pin: ^ar2
|
2017-04-26 18:40:00 +03:00
|
|
|
position_endstop: 0
|
|
|
|
|
position_max: 200
|
2017-07-24 21:12:17 +03:00
|
|
|
homing_speed: 50
|
2017-04-26 18:40:00 +03:00
|
|
|
|
|
|
|
|
[stepper_y]
|
|
|
|
|
step_pin: ar60
|
|
|
|
|
dir_pin: !ar61
|
|
|
|
|
enable_pin: !ar56
|
|
|
|
|
step_distance: .0125
|
|
|
|
|
endstop_pin: ^ar14
|
2017-07-24 20:17:18 +03:00
|
|
|
#endstop_pin: ^ar15
|
2017-04-26 18:40:00 +03:00
|
|
|
position_endstop: 0
|
|
|
|
|
position_max: 200
|
2017-07-24 21:12:17 +03:00
|
|
|
homing_speed: 50
|
2017-04-26 18:40:00 +03:00
|
|
|
|
|
|
|
|
[stepper_z]
|
|
|
|
|
step_pin: ar46
|
|
|
|
|
dir_pin: ar48
|
|
|
|
|
enable_pin: !ar62
|
2018-02-26 00:00:55 +03:00
|
|
|
step_distance: .0025
|
2017-04-26 18:40:00 +03:00
|
|
|
endstop_pin: ^ar18
|
2017-07-24 20:17:18 +03:00
|
|
|
#endstop_pin: ^ar19
|
|
|
|
|
position_endstop: 0.5
|
2017-04-26 18:40:00 +03:00
|
|
|
position_max: 200
|
|
|
|
|
|
|
|
|
|
[extruder]
|
|
|
|
|
step_pin: ar26
|
|
|
|
|
dir_pin: ar28
|
|
|
|
|
enable_pin: !ar24
|
|
|
|
|
step_distance: .002
|
|
|
|
|
nozzle_diameter: 0.400
|
|
|
|
|
filament_diameter: 1.750
|
|
|
|
|
heater_pin: ar10
|
|
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
|
|
|
sensor_pin: analog13
|
|
|
|
|
control: pid
|
|
|
|
|
pid_Kp: 22.2
|
|
|
|
|
pid_Ki: 1.08
|
|
|
|
|
pid_Kd: 114
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 250
|
|
|
|
|
|
2017-07-24 20:17:18 +03:00
|
|
|
#[extruder1]
|
|
|
|
|
#step_pin: ar36
|
|
|
|
|
#dir_pin: ar34
|
|
|
|
|
#enable_pin: !ar30
|
|
|
|
|
#heater_pin: ar9
|
|
|
|
|
#sensor_pin: analog15
|
|
|
|
|
#...
|
|
|
|
|
|
2017-04-26 18:40:00 +03:00
|
|
|
[heater_bed]
|
|
|
|
|
heater_pin: ar8
|
|
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
|
|
|
sensor_pin: analog14
|
|
|
|
|
control: watermark
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 130
|
|
|
|
|
|
|
|
|
|
[fan]
|
|
|
|
|
pin: ar9
|
|
|
|
|
|
|
|
|
|
[mcu]
|
|
|
|
|
serial: /dev/ttyACM0
|
|
|
|
|
pin_map: arduino
|
|
|
|
|
|
|
|
|
|
[printer]
|
|
|
|
|
kinematics: cartesian
|
|
|
|
|
max_velocity: 300
|
|
|
|
|
max_accel: 3000
|
|
|
|
|
max_z_velocity: 5
|
|
|
|
|
max_z_accel: 100
|
2018-02-21 04:50:06 +03:00
|
|
|
|
2019-08-09 19:50:10 +03:00
|
|
|
# Common EXP1 / EXP2 (display) pins
|
|
|
|
|
[board_pins]
|
|
|
|
|
aliases:
|
|
|
|
|
# Common EXP1 header found on many "all-in-one" ramps clones
|
|
|
|
|
EXP1_1=ar37, EXP1_3=ar17, EXP1_5=ar23, EXP1_7=ar27, EXP1_9=<GND>,
|
|
|
|
|
EXP1_2=ar35, EXP1_4=ar16, EXP1_6=ar25, EXP1_8=ar29, EXP1_10=<5V>,
|
|
|
|
|
# EXP2 header
|
|
|
|
|
EXP2_1=ar50, EXP2_3=ar31, EXP2_5=ar33, EXP2_7=ar49, EXP2_9=<GND>,
|
|
|
|
|
EXP2_2=ar52, EXP2_4=ar53, EXP2_6=ar51, EXP2_8=ar41, EXP2_10=<RST>
|
|
|
|
|
# Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "spi"
|
|
|
|
|
# Note, some boards wire: EXP2_8=<RST>, EXP2_10=ar41
|
2018-02-21 04:50:06 +03:00
|
|
|
|
2019-08-09 19:50:10 +03:00
|
|
|
# See the sample-lcd.cfg file for definitions of common LCD displays.
|
