klipper/docs/Pressure_Advance.md

149 lines
7.0 KiB
Markdown
Raw Normal View History

This document provides information on tuning the "pressure advance"
configuration variable for a particular nozzle and filament. The
pressure advance feature can be helpful in reducing ooze. For more
information on how pressure advance is implemented see the
[kinematics](Kinematics.md) document.
Tuning pressure advance
=======================
Pressure advance does two useful things - it reduces ooze during
non-extrude moves and it reduces blobbing during cornering. This guide
uses the second feature (reducing blobbing during cornering) as a
mechanism for tuning.
In order to calibrate pressure advance the printer must be configured
and operational as the tuning test involves printing and inspecting a
test object. It is a good idea to read this document in full prior to
running the test.
Use a slicer to generate g-code for the large hollow square found in
[docs/prints/square_tower.stl](prints/square_tower.stl). Use a high
speed (eg, 100mm/s), zero infill, and a coarse layer height (the layer
height should be around 75% of the nozzle diameter).
Prepare for the test by issuing the following G-Code commands:
```
SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY=1 ACCEL=500
SET_PRESSURE_ADVANCE ADVANCE_LOOKAHEAD_TIME=0
```
These commands make the nozzle travel slower through corners and they
emphasize the effects of extruder pressure. Then for printers with a
direct drive extruder run the command:
```
TUNING_TOWER COMMAND=SET_PRESSURE_ADVANCE PARAMETER=ADVANCE START=0 FACTOR=.005
```
For long bowden extruders use:
```
TUNING_TOWER COMMAND=SET_PRESSURE_ADVANCE PARAMETER=ADVANCE START=0 FACTOR=.020
```
Then print the object. When fully printed the test print looks like:
![tuning_tower](img/tuning_tower.jpg)
The above TUNING_TOWER command instructs Klipper to alter the
pressure_advance setting on each layer of the print. Higher layers in
the print will have a larger pressure advance value set. Layers below
the ideal pressure_advance setting will have blobbing at the corners,
and layers above the ideal setting can lead to rounded corners and
poor extrusion leading up to the corner.
One can cancel the print early if one observes that the corners are no
longer printing well (and thus one can avoid printing layers that are
known to be above the ideal pressure_advance value).
Inspect the print and then use a digital calipers to find the height
that has the best quality corners. When in doubt, prefer a lower
height.
![tune_pa](img/tune_pa.jpg)
The pressure_advance value can then be calculated as `pressure_advance
= <start> + <measured_height> * <factor>`. (For example, `0 + 12.90 *
.020` would be `.258`.)
It is possible to choose custom settings for START and FACTOR if that
helps identify the best pressure advance setting. When doing this, be
sure to issue the TUNING_TOWER command at the start of each test
print.
Typical pressure advance values are between 0.050 and 1.000 (the high
end usually only with bowden extruders). If there is no significant
improvement with a pressure advance up to 1.000, then pressure advance
is unlikely to improve the quality of prints. Return to a default
configuration with pressure advance disabled.
Although this tuning exercise directly improves the quality of
corners, it's worth remembering that a good pressure advance
configuration also reduces ooze throughout the print.
At the completion of this test, update the extruder's pressure_advance
setting in the configuration file and issue a RESTART command. The
RESTART command will clear the test state and return the acceleration
and cornering speeds to their normal values.
Important Notes
===============
* The pressure advance value is dependent on the extruder, the nozzle,
and the filament. It is common for filament from different
manufactures or with different pigments to require significantly
different pressure advance values. Therefore, one should calibrate
pressure advance on each printer and with each spool of filament.
* Printing temperature and extrusion rates can impact pressure
advance. Be sure to tune the extruder
[E steps](http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide#E_steps)
and
[nozzle temperature](http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide#Nozzle_Temperature)
prior to tuning pressure advance.
* It is common for the test print to show different behavior on each
corner. Often the slicer will arrange to change layers at one corner
which can result in that corner being significantly different from
the remaining three corners. If this occurs, then ignore that corner
and tune pressure advance using the other three corners. It is also
common for the remaining corners to vary slightly. (This can occur
due to small differences in how the printer's frame reacts to
cornering in certain directions.) Try to choose a value that works
well for all the remaining corners. If in doubt, prefer a lower
pressure advance value.
* If a high pressure advance value (eg, over 0.200) is used then one
may find that the extruder skips when returning to the printer's
normal acceleration. The pressure advance system accounts for
pressure by pushing in extra filament during acceleration and
retracting that filament during deceleration. With a high
acceleration and high pressure advance the extruder may not have
enough torque to push the required filament. If this occurs, either
use a lower acceleration value or disable pressure advance.
* The pressure_advance_lookahead_time parameter controls how far in
advance to check if a head slow-down is immediately followed by a
speed-up - it reduces pointless pressure changes in the head. It is
recommended to follow the steps above so that it is set to zero
during tuning and to use the default (0.010) during normal prints.
It is possible to tune this setting - higher values will reduce the
amount of pressure change in the nozzle during cornering, but
setting it too high can cause blobbing during cornering. (Tuning
this value is unlikely to impact ooze.) The default of 10ms should
work well on most printers.
* Once pressure advance is tuned in Klipper, it may still be useful to
configure a small retract value in the slicer (eg, 0.75mm) and to
utilize the slicer's "wipe on retract option" if available. These
slicer settings may help counteract ooze caused by filament cohesion
(filament pulled out of the nozzle due to the stickiness of the
plastic). It is recommended to disable the slicer's "z-lift on
retract" option.
* The pressure advance system does not change the timing or path of
the toolhead. A print with pressure advance enabled will take the
same amount of time as a print without pressure advance. Pressure
advance also does not change the total amount of filament extruded
during a print. Pressure advance results in extra extruder movement
during move acceleration and deceleration. A very high pressure
advance setting will result in a very large amount of extruder
movement during acceleration and deceleration, and no configuration
setting places a limit on the amount of that movement.