2018-01-04 06:55:00 +03:00
|
|
|
# This file contains pin mappings for the Wanhao Duplicator i3 Plus
|
|
|
|
|
# (circa 2017). To use this config, the firmware should be compiled
|
|
|
|
|
# for the AVR atmega2560.
|
|
|
|
|
# Pin numbers and other parameters were extracted from the
|
|
|
|
|
# official Marlin source available at:
|
|
|
|
|
# https://github.com/garychen99/Duplicator-i3-plus
|
|
|
|
|
|
|
|
|
|
# See the example.cfg file for a description of available parameters.
|
|
|
|
|
|
|
|
|
|
[stepper_x]
|
|
|
|
|
step_pin: PF7
|
|
|
|
|
dir_pin: !PK0
|
|
|
|
|
enable_pin: !PF6
|
|
|
|
|
step_distance: .0125
|
|
|
|
|
endstop_pin: ^!PF0
|
|
|
|
|
position_endstop: 0
|
|
|
|
|
position_max: 200
|
2018-01-22 02:52:14 +03:00
|
|
|
homing_speed: 30.0
|
2018-01-04 06:55:00 +03:00
|
|
|
|
|
|
|
|
[stepper_y]
|
|
|
|
|
step_pin: PK2
|
|
|
|
|
dir_pin: !PK3
|
|
|
|
|
enable_pin: !PK1
|
|
|
|
|
step_distance: .0125
|
|
|
|
|
endstop_pin: ^!PA2
|
|
|
|
|
position_endstop: 0
|
|
|
|
|
position_max: 200
|
2018-01-22 02:52:14 +03:00
|
|
|
homing_speed: 30.0
|
2018-01-04 06:55:00 +03:00
|
|
|
|
|
|
|
|
[stepper_z]
|
|
|
|
|
step_pin: PK5
|
|
|
|
|
dir_pin: PK7
|
|
|
|
|
enable_pin: !PK4
|
|
|
|
|
step_distance: 0.0025
|
|
|
|
|
endstop_pin: ^!PA1
|
|
|
|
|
position_endstop: 0.5
|
|
|
|
|
position_max: 180
|
|
|
|
|
|
|
|
|
|
[extruder]
|
|
|
|
|
step_pin: PF4
|
|
|
|
|
dir_pin: PF5
|
|
|
|
|
enable_pin: !PF3
|
|
|
|
|
step_distance: 0.010417
|
|
|
|
|
nozzle_diameter: 0.400
|
|
|
|
|
filament_diameter: 1.750
|
|
|
|
|
heater_pin: PG5
|
|
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
|
|
|
sensor_pin: PF1
|
|
|
|
|
control: pid
|
2018-01-22 02:52:14 +03:00
|
|
|
pid_Kp: 30.850721
|
|
|
|
|
pid_Ki: .208175
|
|
|
|
|
pid_Kd: 192.298728
|
2018-01-04 06:55:00 +03:00
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 260
|
|
|
|
|
|
|
|
|
|
[heater_bed]
|
|
|
|
|
heater_pin: PE5
|
|
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
|
|
|
sensor_pin: PK6
|
2018-01-22 02:52:14 +03:00
|
|
|
control: pid
|
|
|
|
|
pid_Kp: 64.095903
|
|
|
|
|
pid_Ki: 1.649830
|
|
|
|
|
pid_Kd: 622.531455
|
2018-01-04 06:55:00 +03:00
|
|
|
min_temp: 0
|
2018-01-22 02:52:14 +03:00
|
|
|
max_temp: 110
|
2018-01-04 06:55:00 +03:00
|
|
|
|
|
|
|
|
[fan]
|
|
|
|
|
pin: PE3
|
|
|
|
|
|
|
|
|
|
[mcu]
|
|
|
|
|
serial: /dev/ttyUSB0
|
|
|
|
|
|
|
|
|
|
[printer]
|
|
|
|
|
kinematics: cartesian
|
|
|
|
|
max_velocity: 300
|
|
|
|
|
max_accel: 800
|
|
|
|
|
max_z_velocity: 5
|
|
|
|
|
max_z_accel: 100
|
