2022-10-22 04:03:57 +03:00
|
|
|
# This file contains pin mappings for the Artillery Sidewinder X2 (2022)
|
|
|
|
|
# with a Artillery_Ruby-v1.2 board. To use this config, during "make menuconfig"
|
|
|
|
|
# select the STM32F401 with "No bootloader" and USB (on PA11/PA12)
|
|
|
|
|
# communication.
|
|
|
|
|
|
|
|
|
|
# To flash this firmware, set the physical bridge between +3.3V and Boot0 PIN
|
|
|
|
|
# on Artillery_Ruby mainboard. Then run the command:
|
|
|
|
|
# make flash FLASH_DEVICE=/dev/serial/by-id/usb-Klipper_stm32f401xc_*-if00
|
|
|
|
|
|
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
|
|
|
|
|
|
[stepper_x]
|
|
|
|
|
step_pin: !PB14
|
|
|
|
|
dir_pin: PB13
|
|
|
|
|
enable_pin: !PB15
|
|
|
|
|
microsteps: 16
|
|
|
|
|
rotation_distance: 40
|
|
|
|
|
endstop_pin: !PA2
|
|
|
|
|
position_endstop: 0
|
|
|
|
|
position_max: 300
|
|
|
|
|
homing_speed: 50
|
|
|
|
|
second_homing_speed: 10
|
|
|
|
|
|
|
|
|
|
[stepper_y]
|
|
|
|
|
step_pin: PB10
|
|
|
|
|
dir_pin: PB2
|
|
|
|
|
enable_pin: !PB12
|
|
|
|
|
microsteps: 16
|
|
|
|
|
rotation_distance: 40
|
|
|
|
|
endstop_pin: !PA1
|
|
|
|
|
position_endstop: 0
|
|
|
|
|
position_max: 300
|
|
|
|
|
homing_speed: 50
|
|
|
|
|
second_homing_speed: 10
|
|
|
|
|
|
|
|
|
|
[stepper_z]
|
|
|
|
|
step_pin: PB0
|
|
|
|
|
dir_pin: !PC5
|
|
|
|
|
enable_pin: !PB1
|
|
|
|
|
microsteps: 16
|
|
|
|
|
rotation_distance: 8
|
|
|
|
|
endstop_pin: probe:z_virtual_endstop
|
|
|
|
|
position_max: 410
|
|
|
|
|
homing_speed: 10
|
|
|
|
|
second_homing_speed: 2
|
|
|
|
|
|
|
|
|
|
[extruder]
|
|
|
|
|
step_pin: PA7
|
|
|
|
|
dir_pin: PA6
|
|
|
|
|
enable_pin: !PC4
|
|
|
|
|
microsteps: 16
|
|
|
|
|
rotation_distance: 20.925
|
|
|
|
|
gear_ratio: 66:22
|
|
|
|
|
nozzle_diameter: 0.400
|
|
|
|
|
filament_diameter: 1.750
|
|
|
|
|
heater_pin: PC9
|
|
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
|
|
|
sensor_pin: PC0
|
|
|
|
|
control: pid
|
|
|
|
|
pid_kp: 20.860
|
|
|
|
|
pid_ki: 1.131
|
|
|
|
|
pid_kd: 96.218
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 250
|
|
|
|
|
|
|
|
|
|
[heater_bed]
|
|
|
|
|
heater_pin: PA8
|
|
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
|
|
|
sensor_pin: PC1
|
|
|
|
|
control: pid
|
|
|
|
|
pid_kp: 42.365
|
|
|
|
|
pid_ki: 0.545
|
|
|
|
|
pid_kd: 822.940
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 130
|
|
|
|
|
|
|
|
|
|
[fan]
|
|
|
|
|
pin: PC8
|
|
|
|
|
off_below: 0.1
|
|
|
|
|
|
|
|
|
|
[heater_fan extruder]
|
|
|
|
|
pin: PC7
|
|
|
|
|
off_below: 0.2
|
|
|
|
|
|
|
|
|
|
[controller_fan case]
|
|
|
|
|
pin: PC6
|
|
|
|
|
off_below: 0.3
|
|
|
|
|
idle_speed: 0.0
|
|
|
|
|
|
|
|
|
|
[temperature_sensor mainboard]
|
|
|
|
|
sensor_type: temperature_mcu
|
|
|
|
|
min_temp: 10
|
|
|
|
|
max_temp: 60
|
|
|
|
|
|
|
|
|
|
[bltouch]
|
|
|
|
|
sensor_pin: PC2
|
|
|
|
|
control_pin: PC3
|
|
|
|
|
x_offset:27.25
|
|
|
|
|
y_offset:-12.8
|
|
|
|
|
z_offset: 1.0
|
|
|
|
|
samples: 3
|
|
|
|
|
samples_tolerance: 0.050
|
|
|
|
|
samples_tolerance_retries: 3
|
|
|
|
|
|
|
|
|
|
[safe_z_home]
|
|
|
|
|
home_xy_position: 150,150
|
|
|
|
|
z_hop: 15
|
|
|
|
|
|
|
|
|
|
[bed_mesh]
|
|
|
|
|
speed: 100
|
|
|
|
|
mesh_min: 27.25, 12.8
|
|
|
|
|
mesh_max: 272.75, 287.2
|
|
|
|
|
algorithm: bicubic
|
|
|
|
|
probe_count: 5,5
|
|
|
|
|
mesh_pps: 3
|
|
|
|
|
fade_end: 10
|
|
|
|
|
|
|
|
|
|
[bed_screws]
|
|
|
|
|
screw1: 50,50
|
|
|
|
|
screw1_name: front left
|
|
|
|
|
screw2: 250,50
|
|
|
|
|
screw2_name: front right
|
|
|
|
|
screw3: 250,250
|
|
|
|
|
screw3_name: back right
|
|
|
|
|
screw4: 50,250
|
|
|
|
|
screw4_name: back left
|
|
|
|
|
speed: 100.0
|
|
|
|
|
|
|
|
|
|
[screws_tilt_adjust]
|
|
|
|
|
screw1: 23,63
|
|
|
|
|
screw1_name: front left
|
|
|
|
|
screw2: 223,63
|
|
|
|
|
screw2_name: front right
|
|
|
|
|
screw3: 223,263
|
2022-12-07 19:02:42 +03:00
|
|
|
screw3_name: back right
|
2022-10-22 04:03:57 +03:00
|
|
|
screw4: 23,263
|
2022-12-07 19:02:42 +03:00
|
|
|
screw4_name: back left
|
2022-10-22 04:03:57 +03:00
|
|
|
speed: 100.0
|
|
|
|
|
screw_thread: CW-M5
|
|
|
|
|
|
|
|
|
|
[mcu]
|
|
|
|
|
serial: /dev/ttyACM0
|
|
|
|
|
|
|
|
|
|
[neopixel extruder]
|
|
|
|
|
pin: PB7
|
|
|
|
|
initial_RED: 1.0
|
|
|
|
|
initial_GREEN: 1.0
|
|
|
|
|
initial_BLUE: 1.0
|
|
|
|
|
|
|
|
|
|
[printer]
|
|
|
|
|
kinematics: cartesian
|
|
|
|
|
max_velocity: 250
|
|
|
|
|
max_accel: 1500
|
|
|
|
|
max_z_velocity: 50
|
|
|
|
|
max_z_accel: 400
|
|
|
|
|
square_corner_velocity: 5.0
|
