76 lines
1.2 KiB
INI
76 lines
1.2 KiB
INI
|
# This file contains pin mappings for the 2017 Creality CR-10S. To use
|
||
|
|
# this config, the firmware should be compiled for the AVR atmega2560.
|
||
|
|
|
||
|
|
# See the example.cfg file for a description of available parameters.
|
||
|
|
|
||
|
|
[stepper_x]
|
||
|
|
step_pin: ar54
|
||
|
|
dir_pin: ar55
|
||
|
|
enable_pin: !ar38
|
||
|
|
step_distance: .0125
|
||
|
|
endstop_pin: ^ar3
|
||
|
|
position_endstop: 0
|
||
|
|
position_max: 300
|
||
|
|
homing_speed: 50
|
||
|
|
|
||
|
|
[stepper_y]
|
||
|
|
step_pin: ar60
|
||
|
|
dir_pin: ar61
|
||
|
|
enable_pin: !ar56
|
||
|
|
step_distance: .0125
|
||
|
|
endstop_pin: ^ar14
|
||
|
|
position_endstop: 0
|
||
|
|
position_max: 300
|
||
|
|
homing_speed: 50
|
||
|
|
|
||
|
|
[stepper_z]
|
||
|
|
step_pin: ar46
|
||
|
|
dir_pin: !ar48
|
||
|
|
enable_pin: !ar62
|
||
|
|
step_distance: .0025
|
||
|
|
endstop_pin: ^ar18
|
||
|
|
position_endstop: 0.5
|
||
|
|
position_max: 200
|
||
|
|
|
||
|
|
[extruder]
|
||
|
|
step_pin: ar26
|
||
|
|
dir_pin: ar28
|
||
|
|
enable_pin: !ar24
|
||
|
|
step_distance: .010526
|
||
|
|
nozzle_diameter: 0.400
|
||
|
|
filament_diameter: 1.750
|
||
|
|
heater_pin: ar10
|
||
|
|
sensor_type: EPCOS 100K B57560G104F
|
||
|
|
sensor_pin: analog13
|
||
|
|
control: pid
|
||
|
|
pid_Kp: 22.2
|
||
|
|
pid_Ki: 1.08
|
||
|
|
pid_Kd: 114
|
||
|
|
min_temp: 0
|
||
|
|
max_temp: 250
|
||
|
|
|
||
|
|
[heater_bed]
|
||
|
|
heater_pin: ar8
|
||
|
|
sensor_type: EPCOS 100K B57560G104F
|
||
|
|
sensor_pin: analog14
|
||
|
|
control: pid
|
||
|
|
pid_Kp: 690.34
|
||
|
|
pid_Ki: 111.47
|
||
|
|
pid_Kd: 1068.83
|
||
|
|
min_temp: 0
|
||
|
|
max_temp: 130
|
||
|
|
|
||
|
|
[fan]
|
||
|
|
pin: ar9
|
||
|
|
|
||
|
|
[mcu]
|
||
|
|
serial: /dev/ttyUSB0
|
||
|
|
pin_map: arduino
|
||
|
|
|
||
|
|
[printer]
|
||
|
|
kinematics: cartesian
|
||
|
|
max_velocity: 300
|
||
|
|
max_accel: 3000
|
||
|
|
max_z_velocity: 5
|
||
|
|
max_z_accel: 100
|