134 lines
2.5 KiB
INI
134 lines
2.5 KiB
INI
|
# This file contains a configuration for the Anycubic Kobra Go printer.
|
||
|
|
#
|
||
|
|
# See docs/Config_Reference.md for a description of parameters.
|
||
|
|
#
|
||
|
|
# To build the firmware, use the following configuration:
|
||
|
|
# - Micro-controller: Huada Semiconductor HC32F460
|
||
|
|
# - Communication interface: Serial (PA3 & PA2) - Anycubic
|
||
|
|
#
|
||
|
|
# Installation:
|
||
|
|
# 1. Rename the klipper bin to `firmware.bin` and copy it to an SD Card.
|
||
|
|
# 2. Power off the Printer, insert the SD Card and power it on.
|
||
|
|
# 3. The the LCD will be stuck on the Firmware-update screen.
|
||
|
|
# Just Wait for 3-5 minutes to ensure the firmware is flashed.
|
||
|
|
# 4. After waiting, shutdown the printer and remove the SD Card.
|
||
|
|
|
||
|
|
[stepper_x]
|
||
|
|
step_pin: PA12
|
||
|
|
dir_pin: PA11
|
||
|
|
enable_pin: !PA15
|
||
|
|
microsteps: 16
|
||
|
|
rotation_distance: 40
|
||
|
|
endstop_pin: !PH2
|
||
|
|
position_endstop: -13
|
||
|
|
position_min:-13
|
||
|
|
position_max: 238
|
||
|
|
homing_speed: 50
|
||
|
|
|
||
|
|
[stepper_y]
|
||
|
|
step_pin: PA9
|
||
|
|
dir_pin: PA8
|
||
|
|
enable_pin: !PA15
|
||
|
|
microsteps: 16
|
||
|
|
rotation_distance: 40
|
||
|
|
endstop_pin: ^!PC13
|
||
|
|
position_endstop: -9
|
||
|
|
position_min:-9
|
||
|
|
position_max: 238
|
||
|
|
homing_speed: 50
|
||
|
|
|
||
|
|
[stepper_z]
|
||
|
|
step_pin: PC7
|
||
|
|
dir_pin: !PC6
|
||
|
|
enable_pin: !PA15
|
||
|
|
microsteps: 16
|
||
|
|
rotation_distance: 8
|
||
|
|
endstop_pin: ^PC14
|
||
|
|
position_endstop: 0
|
||
|
|
position_min: -10
|
||
|
|
position_max: 250
|
||
|
|
homing_speed: 5
|
||
|
|
|
||
|
|
[extruder]
|
||
|
|
step_pin: PB15
|
||
|
|
dir_pin: PB14
|
||
|
|
enable_pin: !PA15
|
||
|
|
microsteps: 16
|
||
|
|
rotation_distance: 31.07
|
||
|
|
max_extrude_only_velocity: 25
|
||
|
|
max_extrude_only_accel: 1000
|
||
|
|
nozzle_diameter: 0.400
|
||
|
|
filament_diameter: 1.750
|
||
|
|
heater_pin: PB8
|
||
|
|
sensor_type: ATC Semitec 104GT-2
|
||
|
|
sensor_pin: PC3
|
||
|
|
min_extrude_temp: 170
|
||
|
|
min_temp: 0
|
||
|
|
max_temp: 250
|
||
|
|
control: pid
|
||
|
|
pid_kp: 19.56
|
||
|
|
pid_ki: 1.62
|
||
|
|
pid_kd: 200.00
|
||
|
|
|
||
|
|
[heater_bed]
|
||
|
|
heater_pin: PB9
|
||
|
|
sensor_type: EPCOS 100K B57560G104F
|
||
|
|
sensor_pin: PC1
|
||
|
|
min_temp: 0
|
||
|
|
max_temp: 120
|
||
|
|
control: pid
|
||
|
|
pid_kp: 97.1
|
||
|
|
pid_ki: 1.41
|
||
|
|
pid_kd: 1675.16
|
||
|
|
|
||
|
|
[bed_mesh]
|
||
|
|
speed: 200
|
||
|
|
horizontal_move_z: 2.5
|
||
|
|
mesh_min: 5, 5
|
||
|
|
mesh_max: 217.2, 207.8
|
||
|
|
probe_count: 5, 5
|
||
|
|
|
||
|
|
[probe]
|
||
|
|
pin: PA1
|
||
|
|
x_offset: -20.8
|
||
|
|
y_offset: 0
|
||
|
|
z_offset: 0
|
||
|
|
samples: 3
|
||
|
|
samples_result: average
|
||
|
|
samples_tolerance_retries: 3
|
||
|
|
sample_retract_dist: 0.5
|
||
|
|
speed: 2
|
||
|
|
lift_speed: 4
|
||
|
|
|
||
|
|
[safe_z_home]
|
||
|
|
home_xy_position: 0, 0
|
||
|
|
speed: 5
|
||
|
|
z_hop: 10
|
||
|
|
z_hop_speed: 15
|
||
|
|
|
||
|
|
[controller_fan controller_fan]
|
||
|
|
pin: PB12
|
||
|
|
|
||
|
|
[heater_fan extruder_fan]
|
||
|
|
pin: PB13
|
||
|
|
|
||
|
|
[fan]
|
||
|
|
pin: PB5
|
||
|
|
cycle_time: 0.00005 #20kHz
|
||
|
|
|
||
|
|
[output_pin enable_pin]
|
||
|
|
pin: PB6
|
||
|
|
static_value: 1
|
||
|
|
#This pin enables the bed, hotend, extruder fan, part fan.
|
||
|
|
|
||
|
|
[mcu]
|
||
|
|
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
|
||
|
|
restart_method: command
|
||
|
|
|
||
|
|
[printer]
|
||
|
|
kinematics: cartesian
|
||
|
|
max_velocity: 300
|
||
|
|
max_accel: 500
|
||
|
|
max_z_velocity: 4
|
||
|
|
max_z_accel: 100
|