155 lines
3.1 KiB
INI
155 lines
3.1 KiB
INI
|
# This file contains pin mappings for the Creality CR-10S Pro V2. To use
|
||
|
|
# this config, the firmware should be compiled for the AVR atmega2560.
|
||
|
|
|
||
|
|
# See docs/Config_Reference.md for a description of parameters.
|
||
|
|
|
||
|
|
## General Config
|
||
|
|
[mcu]
|
||
|
|
serial: /dev/serial/by-id/<YOUR_USB_ID>
|
||
|
|
|
||
|
|
[printer]
|
||
|
|
kinematics: cartesian
|
||
|
|
max_velocity: 200
|
||
|
|
max_accel: 1500
|
||
|
|
max_z_velocity: 10
|
||
|
|
max_z_accel: 100
|
||
|
|
|
||
|
|
## Stepper Motors and Extruder
|
||
|
|
[stepper_x]
|
||
|
|
step_pin: PF0 #ar54
|
||
|
|
dir_pin: PF1 #ar55
|
||
|
|
enable_pin: !PD7 #!ar38
|
||
|
|
rotation_distance: 40
|
||
|
|
microsteps: 16
|
||
|
|
full_steps_per_rotation: 200
|
||
|
|
endstop_pin: ^PE5 #^ar3
|
||
|
|
position_endstop: 0
|
||
|
|
position_min: 0
|
||
|
|
position_max: 300
|
||
|
|
homing_speed: 50
|
||
|
|
homing_retract_dist: 5
|
||
|
|
|
||
|
|
[stepper_y]
|
||
|
|
step_pin: PF6 #ar60
|
||
|
|
dir_pin: !PF7 #ar61
|
||
|
|
enable_pin: !PF2 #!ar56
|
||
|
|
rotation_distance: 40
|
||
|
|
microsteps: 16
|
||
|
|
full_steps_per_rotation: 200
|
||
|
|
endstop_pin: ^PJ1 #^ar14
|
||
|
|
position_endstop: 0
|
||
|
|
position_min: 0
|
||
|
|
position_max: 310
|
||
|
|
homing_speed: 50
|
||
|
|
homing_retract_dist: 5
|
||
|
|
|
||
|
|
[stepper_z]
|
||
|
|
step_pin: PL3 #ar46
|
||
|
|
dir_pin: !PL1 #!ar48
|
||
|
|
enable_pin: !PK0 #!ar62
|
||
|
|
rotation_distance: 8
|
||
|
|
microsteps: 16
|
||
|
|
full_steps_per_rotation: 200
|
||
|
|
endstop_pin: probe:z_virtual_endstop
|
||
|
|
position_min: -3
|
||
|
|
position_max: 363 # you can go higher but then the cables crimp
|
||
|
|
|
||
|
|
[extruder]
|
||
|
|
step_pin: PA4 # ar26
|
||
|
|
dir_pin: PA6 # !ar28
|
||
|
|
enable_pin: !PA2 # !ar24
|
||
|
|
rotation_distance: 22.900
|
||
|
|
microsteps: 16
|
||
|
|
full_steps_per_rotation: 200
|
||
|
|
nozzle_diameter: 0.400
|
||
|
|
filament_diameter: 1.750
|
||
|
|
max_extrude_only_distance: 500.0
|
||
|
|
max_extrude_only_velocity: 70.0
|
||
|
|
max_extrude_only_accel: 1000.0
|
||
|
|
heater_pin: PB4 #ar10
|
||
|
|
sensor_type: EPCOS 100K B57560G104F
|
||
|
|
sensor_pin: PK5 #analog13
|
||
|
|
control: pid #calibrated in Klipper, you will need to run this for your machine
|
||
|
|
pid_kp: 28.359
|
||
|
|
pid_ki: 1.616
|
||
|
|
pid_kd: 124.426
|
||
|
|
min_extrude_temp: 170
|
||
|
|
min_temp: 5
|
||
|
|
max_temp: 275
|
||
|
|
|
||
|
|
[fan]
|
||
|
|
pin: PH6 #ar9
|
||
|
|
|
||
|
|
[heater_bed]
|
||
|
|
heater_pin: PH5 #ar8
|
||
|
|
sensor_type: EPCOS 100K B57560G104F
|
||
|
|
sensor_pin: PK6 #analog14
|
||
|
|
control: pid #calibrated in Klipper, you will need to run this for your machine
|
||
|
|
pid_kp: 70.936
|
||
|
|
pid_ki: 1.151
|
||
|
|
pid_kd: 1093.298
|
||
|
|
min_temp: 5
|
||
|
|
max_temp: 140
|
||
|
|
|
||
|
|
## BLTouch and Safe Z Settings
|
||
|
|
[bltouch]
|
||
|
|
sensor_pin: ^PD2
|
||
|
|
control_pin: PB5
|
||
|
|
stow_on_each_sample: False # Be careful
|
||
|
|
probe_with_touch_mode: True
|
||
|
|
x_offset: -27
|
||
|
|
y_offset: -2
|
||
|
|
z_offset: 2 # you will need to calibrate this in Klipper
|
||
|
|
speed: 4.0
|
||
|
|
samples: 2
|
||
|
|
sample_retract_dist: 3.0
|
||
|
|
|
||
|
|
[safe_z_home]
|
||
|
|
home_xy_position: 177,155
|
||
|
|
speed: 80.0
|
||
|
|
z_hop: 10.0
|
||
|
|
z_hop_speed: 5.0
|
||
|
|
|
||
|
|
[bed_mesh]
|
||
|
|
speed: 120
|
||
|
|
horizontal_move_z: 5
|
||
|
|
mesh_min: 5, 5
|
||
|
|
mesh_max: 268, 305
|
||
|
|
probe_count: 5,5
|
||
|
|
fade_start: 1
|
||
|
|
fade_end: 10
|
||
|
|
|
||
|
|
[filament_switch_sensor e0_sensor]
|
||
|
|
switch_pin: PE4 #ar2
|
||
|
|
pause_on_runout: False
|
||
|
|
runout_gcode:
|
||
|
|
PAUSE_PARK
|
||
|
|
|
||
|
|
## Calibrating the Bed
|
||
|
|
# this is for the bltouch to calibrate the bed
|
||
|
|
[screws_tilt_adjust]
|
||
|
|
screw1: 40,40
|
||
|
|
screw1_name: front left screw
|
||
|
|
screw2: 295,40
|
||
|
|
screw2_name: front right screw
|
||
|
|
screw3: 295,280
|
||
|
|
screw3_name: rear right screw
|
||
|
|
screw4: 40,280
|
||
|
|
screw4_name: rear left screw
|
||
|
|
speed: 50
|
||
|
|
horizontal_move_z: 10
|
||
|
|
screw_thread: CW-M3
|
||
|
|
|
||
|
|
[bed_screws]
|
||
|
|
screw1: 13,38
|
||
|
|
screw1_name: front left screw
|
||
|
|
screw2: 268,38
|
||
|
|
screw2_name: front right screw
|
||
|
|
screw3: 268,278
|
||
|
|
screw3_name: rear right screw
|
||
|
|
screw4: 13,38
|
||
|
|
screw4_name: rear left screw
|
||
|
|
horizontal_move_z: 5
|
||
|
|
|
||
|
|
[pause_resume]
|