3diy
/
klipper
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
klipper/src/Kconfig

69 lines
1.6 KiB
Plaintext
Raw Normal View History

Initial commit of source code. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2016-05-25 18:37:40 +03:00
# Main Kconfig settings
mainmenu "Klipper Firmware Configuration"
choice
prompt "Micro-controller Architecture"
config MACH_AVR
bool "Atmega AVR"
sam3x8e: Add initial support for Arduino Due boards This adds basic support for running on the Atmel SAM3x8e micro-controllers that are found in the Arudino Due boards. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2016-06-14 21:27:30 +03:00
config MACH_SAM3X8E
bool "SAM3x8e (Arduino Due)"
samd21: Initial support for SAMD21 micro-controllers Add initial support for the Atmel SAMD21 micro-controllers. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-07-28 02:22:44 +03:00
config MACH_SAMD21
bool "SAMD21 (Arduino Zero)"
sam4e8e: Add the SAM4e8e port This can be flashed to e.g. the duet wifi using bossac. It requires a later version as is currently included in the klipper repo (1.8 vs. 1.2). Comms are currently via UART0 only, USB serial is still TBD Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
2018-08-07 02:03:54 +03:00
config MACH_SAM4E8E
bool "SAM4e8e (Duet Wifi/Eth)"
lpc176x: Add initial support for LPC176x processors Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-05-08 04:32:27 +03:00
config MACH_LPC176X
bool "LPC176x (Smoothieboard)"
Add STM32F103 port Add a fully functional STM32F1 port, currently mostly targeting STM32F103 microcontrollers. This requires an 8 MHz XTAL. The maximum possible step rate is around 282K steps per second. This uses stm32flash to burn the firmware. The bootloader needs to be started by setting BOOT0 to 1 and resetting the MCU. There is no automatic bootloader, unlike on Arduino. Signed-off-by: Grigori Goronzy <greg@kinoho.net>
2018-03-31 16:34:59 +03:00
config MACH_STM32F1
bool "STMicroelectronics STM32F103"
pru: Initial support for the Beaglebone PRU Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-05-07 04:47:04 +03:00
config MACH_PRU
bool "Beaglebone PRU"
linux: Initial support for running Klipper in a Linux real-time process Add support for compiling the Klipper micro-controller code as a real-time process capable of running on standard Linux systems. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-07-20 07:02:43 +03:00
config MACH_LINUX
bool "Linux process"
Initial commit of source code. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2016-05-25 18:37:40 +03:00
config MACH_SIMU
bool "Host simulator"
endchoice
source "src/avr/Kconfig"
sam3x8e: Add initial support for Arduino Due boards This adds basic support for running on the Atmel SAM3x8e micro-controllers that are found in the Arudino Due boards. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2016-06-14 21:27:30 +03:00
source "src/sam3x8e/Kconfig"
samd21: Initial support for SAMD21 micro-controllers Add initial support for the Atmel SAMD21 micro-controllers. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-07-28 02:22:44 +03:00
source "src/samd21/Kconfig"
sam4e8e: Add the SAM4e8e port This can be flashed to e.g. the duet wifi using bossac. It requires a later version as is currently included in the klipper repo (1.8 vs. 1.2). Comms are currently via UART0 only, USB serial is still TBD Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
2018-08-07 02:03:54 +03:00
source "src/sam4e8e/Kconfig"
lpc176x: Add initial support for LPC176x processors Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-05-08 04:32:27 +03:00
source "src/lpc176x/Kconfig"
Add STM32F103 port Add a fully functional STM32F1 port, currently mostly targeting STM32F103 microcontrollers. This requires an 8 MHz XTAL. The maximum possible step rate is around 282K steps per second. This uses stm32flash to burn the firmware. The bootloader needs to be started by setting BOOT0 to 1 and resetting the MCU. There is no automatic bootloader, unlike on Arduino. Signed-off-by: Grigori Goronzy <greg@kinoho.net>
2018-03-31 16:34:59 +03:00
source "src/stm32f1/Kconfig"
pru: Initial support for the Beaglebone PRU Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-05-07 04:47:04 +03:00
source "src/pru/Kconfig"
linux: Initial support for running Klipper in a Linux real-time process Add support for compiling the Klipper micro-controller code as a real-time process capable of running on standard Linux systems. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-07-20 07:02:43 +03:00
source "src/linux/Kconfig"
Initial commit of source code. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2016-05-25 18:37:40 +03:00
source "src/simulator/Kconfig"
sam4e8e: Add the SAM4e8e port This can be flashed to e.g. the duet wifi using bossac. It requires a later version as is currently included in the klipper repo (1.8 vs. 1.2). Comms are currently via UART0 only, USB serial is still TBD Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
2018-08-07 02:03:54 +03:00
gpiocmds: Add Kconfig option to allow boards to disable ADC commands Some boards may not support the ADC hardware. Update the build so that those commands do not need to be compiled if they are not available. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2016-06-09 02:32:06 +03:00
# The HAVE_GPIO_x options allow boards to disable support for some
# commands if the hardware does not support the feature.
build: Allow boards to disable digital input/output support Allow the micro-controller code to be built without support for regular gpio pins. In this case, the code for endstops, steppers, and gpiocmds will be disabled. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-07-20 06:59:35 +03:00
config HAVE_GPIO
bool
default n
gpiocmds: Add Kconfig option to allow boards to disable ADC commands Some boards may not support the ADC hardware. Update the build so that those commands do not need to be compiled if they are not available. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2016-06-09 02:32:06 +03:00
config HAVE_GPIO_ADC
bool
default n
spicmds: Add Kconfig option to allow boards to disable SPI commands Some boards may not support SPI transfers. Update the build so that those commands do not need to be compiled if they are not available. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2016-06-09 02:35:45 +03:00
config HAVE_GPIO_SPI
bool
default n
pwmcmds: Add Kconfig option to allow boards to disable hardware PWM commands Some boards may not support hardware based PWM. Update the build so that those commands do not need to be compiled if they are not available. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2016-06-09 02:44:34 +03:00
config HAVE_GPIO_HARD_PWM
bool
default n
Kconfig: Rename HAVE_USER_INTERFACE to HAVE_GPIO_BITBANGING Rename the HAVE_USER_INTERFACE definition in preparation for other "bit banging" interfaces. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-08-27 18:09:47 +03:00
config HAVE_GPIO_BITBANGING
lcd_st7920: Add micro-controller code for the ST7920 LCD chip Add support for passing messages to an ST7920 chip via a SPI bit-banging interface. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-02-21 04:47:02 +03:00
bool
default n
gpiocmds: Add Kconfig option to allow boards to disable ADC commands Some boards may not support the ADC hardware. Update the build so that those commands do not need to be compiled if they are not available. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2016-06-09 02:32:06 +03:00
stepper: Support rescheduling of step events on faster MCUs On faster MCUs the step and unstep events may be too close for the stepper motor driver. Add a CONFIG_NO_UNSTEP_DELAY build option and support the case where it is not set. This allows faster MCUs to schedule two events for each step (one for the step and one for the unstep). Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2016-06-14 02:42:34 +03:00
config NO_UNSTEP_DELAY
# Slow micro-controllers do not require a delay before returning a
# stepper step pin to its default level. A board can enable this
# option to optimize the stepper_event() handler in this case.
bool
default n
Initial commit of source code. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2016-05-25 18:37:40 +03:00
config INLINE_STEPPER_HACK
# Enables gcc to inline stepper_event() into the main timer irq handler
bool
build: Allow boards to disable digital input/output support Allow the micro-controller code to be built without support for regular gpio pins. In this case, the code for endstops, steppers, and gpiocmds will be disabled. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-07-20 06:59:35 +03:00
depends on HAVE_GPIO
sam3x8e: Add initial support for Arduino Due boards This adds basic support for running on the Atmel SAM3x8e micro-controllers that are found in the Arudino Due boards. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2016-06-14 21:27:30 +03:00
default y