132 lines
2.6 KiB
INI
132 lines
2.6 KiB
INI
|
# This file contains pin mappings for the stock 2022 Creality Ender 3
|
||
|
|
# S1 Plus. To use this config check the STM32 Chip on the Mainboard,
|
||
|
|
# during "make menuconfig" select accordingly either the
|
||
|
|
# STM32F103 with "28KiB bootloader" or the STM32F401 with
|
||
|
|
# "64KiB bootloader" and serial (on USART1 PA10/PA9) for both.
|
||
|
|
|
||
|
|
# For a direct serial connection, in "make menuconfig" select
|
||
|
|
# "Enable extra low-level configuration options" and Serial
|
||
|
|
# (on USART2 PA3/PA2), which is on the 10 pin IDC cable used
|
||
|
|
# for the LCD module as follows: 3: Tx, 4: Rx, 9: GND, 10: VCC
|
||
|
|
|
||
|
|
# Flash this firmware by copying "out/klipper.bin" to a SD card and
|
||
|
|
# turning on the printer with the card inserted. The filename
|
||
|
|
# must be changed to "firmware.bin"
|
||
|
|
|
||
|
|
# With STM32F401, you might need to put "firmware.bin" in a
|
||
|
|
# folder on the SD card called "STM32F4_UPDATE" in order to flash.
|
||
|
|
|
||
|
|
# See docs/Config_Reference.md for a description of parameters.
|
||
|
|
|
||
|
|
[stepper_x]
|
||
|
|
step_pin: PC2
|
||
|
|
dir_pin: PB9
|
||
|
|
enable_pin: !PC3
|
||
|
|
microsteps: 16
|
||
|
|
rotation_distance: 40
|
||
|
|
endstop_pin: !PA5
|
||
|
|
position_endstop: -10
|
||
|
|
position_max: 316
|
||
|
|
position_min: -15
|
||
|
|
homing_speed: 50
|
||
|
|
|
||
|
|
[stepper_y]
|
||
|
|
step_pin: PB8
|
||
|
|
dir_pin: PB7
|
||
|
|
enable_pin: !PC3
|
||
|
|
microsteps: 16
|
||
|
|
rotation_distance: 40
|
||
|
|
endstop_pin: !PA6
|
||
|
|
position_endstop: -10
|
||
|
|
position_max: 304
|
||
|
|
position_min: -15
|
||
|
|
homing_speed: 50
|
||
|
|
|
||
|
|
[stepper_z]
|
||
|
|
step_pin: PB6
|
||
|
|
dir_pin: !PB5
|
||
|
|
enable_pin: !PC3
|
||
|
|
microsteps: 16
|
||
|
|
rotation_distance: 8
|
||
|
|
endstop_pin: probe:z_virtual_endstop
|
||
|
|
position_max: 300
|
||
|
|
position_min: -4
|
||
|
|
|
||
|
|
[extruder]
|
||
|
|
step_pin: PB4
|
||
|
|
dir_pin: PB3
|
||
|
|
enable_pin: !PC3
|
||
|
|
microsteps: 16
|
||
|
|
gear_ratio: 42:12
|
||
|
|
rotation_distance: 26.359
|
||
|
|
nozzle_diameter: 0.400
|
||
|
|
filament_diameter: 1.750
|
||
|
|
heater_pin: PA1
|
||
|
|
sensor_type: EPCOS 100K B57560G104F
|
||
|
|
sensor_pin: PC5
|
||
|
|
control: pid
|
||
|
|
pid_Kp: 23.561
|
||
|
|
pid_Ki: 1.208
|
||
|
|
pid_Kd: 114.859
|
||
|
|
min_temp: 0
|
||
|
|
max_temp: 260
|
||
|
|
|
||
|
|
[heater_bed]
|
||
|
|
heater_pin: PA7
|
||
|
|
sensor_type: EPCOS 100K B57560G104F
|
||
|
|
sensor_pin: PC4
|
||
|
|
control: pid
|
||
|
|
pid_Kp: 71.867
|
||
|
|
pid_Ki: 1.536
|
||
|
|
pid_Kd: 840.843
|
||
|
|
min_temp: 0
|
||
|
|
max_temp: 100
|
||
|
|
|
||
|
|
[heater_fan hotend_fan]
|
||
|
|
pin: PC0
|
||
|
|
|
||
|
|
[fan]
|
||
|
|
pin: PA0
|
||
|
|
|
||
|
|
[mcu]
|
||
|
|
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
|
||
|
|
restart_method: command
|
||
|
|
|
||
|
|
[printer]
|
||
|
|
kinematics: cartesian
|
||
|
|
max_velocity: 300
|
||
|
|
max_accel: 2000
|
||
|
|
max_z_velocity: 5
|
||
|
|
max_z_accel: 100
|
||
|
|
|
||
|
|
[bltouch]
|
||
|
|
sensor_pin: ^PC14
|
||
|
|
control_pin: PC13
|
||
|
|
x_offset: -31.8
|
||
|
|
y_offset: -40.5
|
||
|
|
z_offset: 0
|
||
|
|
probe_with_touch_mode: true
|
||
|
|
stow_on_each_sample: false
|
||
|
|
|
||
|
|
[bed_mesh]
|
||
|
|
speed: 120
|
||
|
|
mesh_min: 20, 20
|
||
|
|
mesh_max: 283, 263
|
||
|
|
probe_count: 4,4
|
||
|
|
algorithm: bicubic
|
||
|
|
|
||
|
|
[safe_z_home]
|
||
|
|
home_xy_position: 187, 192
|
||
|
|
speed: 75
|
||
|
|
z_hop: 10
|
||
|
|
z_hop_speed: 5
|
||
|
|
move_to_previous: true
|
||
|
|
|
||
|
|
[filament_switch_sensor e0_sensor]
|
||
|
|
switch_pin: !PC15
|
||
|
|
pause_on_runout: true
|
||
|
|
runout_gcode: PAUSE
|
||
|
|
|
||
|
|
[pause_resume]
|
||
|
|
recover_velocity: 25
|